A charging report that says a vehicle was plugged in for eight hours may tell a fleet very little about what happened overnight. The vehicle could have been waiting for a charging window, sharing power with other bays or sitting connected after charging finished. When a pilot starts missing departures, the useful question is where the time and energy went. A depot energy log gives facilities and dispatch a shared way to answer it.
Start with a small group of vehicles using the same site. Keep the log simple enough that the person closing the yard and the person opening it can both maintain it. The records should answer three questions by morning: which vehicles charged, how much energy each session delivered, and whether every assigned vehicle left with enough charge for its work.
Record the time windows that control charging
Give each vehicle a consistent identifier and label each charging bay. Record the vehicle’s return time, when its cable was connected, when charging began, when charging stopped and its planned departure. If the charger reports a session ID, add it. That lets the fleet match its dispatch records to the charger export without relying on someone to remember which van was in which bay.
Track the schedule the depot actually operates. A van that comes back at 5 p.m. may need to remain available for unloading until 6 p.m. A bay may be occupied by a vehicle awaiting service, or a cable might only reach one side of a crowded parking lane. Add a short reason field for those interruptions. A recurring reason is easier to act on than a column of late departures with no context.
Record when a charger shows the cable is connected but the session has not begun. Some vehicles or chargers wait for scheduled start times. Others may need a successful authorization step. If a delayed session is intentional, record the planned start. That distinction helps separate schedule design from a hardware or account problem.
Put kW and kWh in separate columns
Power in kilowatts describes the rate at which electricity is delivered. Energy in kilowatt-hours is the amount delivered over time. A charger running at 6 kW for four hours supplies 24 kWh at the charger’s measurement point. If it supplies 4 kW for two hours and 6 kW for two more, the total is 20 kWh. A charger can report a high peak power while delivering relatively little energy across an entire session.
Use the charger export for delivered energy, and record the vehicle’s state of charge at arrival and departure when available. Keep these readings apart. The energy drawn from the charging equipment can differ from the change recorded by the vehicle, especially when equipment or battery conditioning uses energy. For comparing several vehicles, use the same measurement point on each one and note which data came from the charger or vehicle.
A fleet planning a larger installation can use federal guidance to organize conversations about operating patterns, infrastructure and site requirements. Site-specific power limits, tariffs and installation details come from the utility and qualified project team. U.S. Department of Energy guidance on managed fleet charging.
Look for the difference between site limits and vehicle limits
When a vehicle draws less power than expected, start by asking what else was running at the same time. Several vehicles may have shared a site power limit. The vehicle itself may have requested less power. A scheduled rule may have held charging until another activity finished. If the charger export includes power readings over time, compare them with the bay assignments and operating schedule. A change that occurs when a second vehicle plugs in points to a different issue than one that happens whenever the same truck reaches a similar state of charge.
Facilities may also have information from the site meter. Comparing meter peaks with charger sessions can help identify whether charging coincides with other major loads. Ask the utility how it defines a billing demand interval and which meter the tariff uses. A high one-minute reading and a billing demand interval can tell different stories. Keep the utility’s definitions with the records so that the pilot does not confuse a temporary spike with a cost on the bill.
Try one scheduling change at a time
Suppose three vehicles return to two usable bays. One needs to leave early, another can depart later and the third has plenty of charge. Put the early vehicle first and record how long it takes to reach the agreed departure level. Then decide whether the later vehicle has enough time if its charging is delayed. A charger-management system can help allocate power, but the depot still needs to know which departure matters most and when the schedule has changed.
Choose a few nights with similar operations before comparing results. If the fleet changes bay assignments, charging start times and vehicle routes on the same day, it will be hard to know what caused an improvement. Keep the changes small enough to reverse. For example, test a priority bay for early departures before installing more hardware on the assumption that every truck must charge as soon as it returns.
Review exceptions with dispatch and facilities
At the end of the week, review every departure below the fleet’s agreed charge threshold. Distinguish a late return, a charger fault, a bay conflict and an unusually demanding shift. Those cases call for different decisions. A charger fault might need a service ticket and an alternate bay. An unusually demanding shift might call for a different vehicle assignment. A repeated authorization error might be fixed through training or an account setting.
Give the morning dispatcher a short list of actions for each common exception. Include the charge threshold for a backup vehicle, which bays can be reassigned and who should be contacted when a session fails. If the charger system can send alerts, test whether the intended person receives and understands them. A warning at midnight helps only if someone has the authority and practical means to act on it.
Use the log before buying more equipment
After several weeks, use the records to estimate how many vehicles need energy at the same time, how often the yard runs out of usable bays, and whether each planned departure can be served under the proposed power limit. Look at a difficult operating week alongside the average one. Ask the team to model one blocked bay or a vehicle that returns two hours late, then check whether the rest of the schedule still holds.
Bring those results to the utility and installation team. A concrete record of simultaneous sessions, departure requirements and exceptions makes it easier to discuss capacity and layout. Keep using the same fields after a new charger is installed. The first week of operation can then be compared with the pilot on the same basis, and the depot can tell whether it gained reliable departures or simply added more equipment.
Keep a short description of each change beside the log. Moving a bay, revising a vehicle schedule or changing a charger limit can affect results immediately. Recording when those decisions took effect lets a later reviewer compare similar operating weeks and trace a recurring problem back to its start.